Hello NigeApologies for direct approach but I have knacked my CD70 up and any help would be REALLY appreciated.I have lurked on this site for a while and today took the plunge to follow your advice on updating my CD70 firmware on my 2007 Vectra SRi.I downloaded the software and burnt at low speed and went through the upgrade procedure. Unfortunately my disc must have been useless and the display on the CD70 hung on Software Update for hours.I had to turn the ignition off and so I am stuck with a dead CD70.
Jan 22, 2018 - NAVTEQ Europe Opel CD70 Version 2012 2013.rar.torrent DOWNLOAD.
I have removed the fuse and managed to get the suspect CD out. Currently my CD 70 only shows the BC functions and nothing else.From surfing around I understand the best recovery method is to remove fuse then re-insert and reset the EEPROM. Then re-update with a reliable disc.I am struggling with the EEPROM part, it maybe simple but I cant find this option in the Testmode. Can you give me an idiots guide please.Can you also advise if you think i am doing the right thing in general.
Sorry to waffle on but I am bricking it in case I cant fix it and the Mrs finds out I have been 'messing with stuff I shouldnt again'!!!!!!Many thanks.ET. PANIC OVER!Sorted myself - finally got a decent image burnt to disc and just stuck it in the machine and turned the ignition on. CD70 immediately started the update and all was well at the end kept my stations and navi destinations.No messing with system settings, eeproms or fuses!If you do see this Nige thanks in any case for your earlier advice to other people. It still helped.ETHow did you make decent image ( what software, burning speed, disc manufacturer, burn mode)?
I have also tried to update software on cd70 and now it's stuck. Radio and navi don't work. Only board computer works.
I have to remove fuse because screen does't turn off. I burned four discs with software update and none of them works. BokiilicI used cheapo media (Teco CD's) and I think that was the cause of the problem.I also burned using several software apps (IMGburn, Nero and MagicISO).My successful burn was with my cheapo Tesco CD burnt on MagicISO at the slowest speed you can specify - mine was x4.I then turned ignition key on put the fuse back in and loaded this newly burnt cd.I noticed with mine that the percentage bar didnt seem to move for 5mins or so. Dont panic if the percentage bar takes ages - initially I was told the whole process was 5-10 mins, mine took nearly 30mins from start to finish.Good Luck and keep me informed. Hi, i am reading this with much interest, i too would like to update my cd70 unit but not sure now? Hello!I got the official update CD and tried to update my unit but it showed an error and now the disk is stuck in the unit, can't eject it.
What should I do?Thank you in advance!I assume you put the update CD in the Navi slot?This happened to me on a couple of occasions, I had to remove the fuse number 35 out of the fuse box located under the bonnet (Astra that is).I then put the ignition on, put the fuse back in and ran to the CD70 unit. I kept pressing eject till it came out. When this failed I actually wedged another CD into the navi slow, so that it was positioned below the actively spinning stuck disk. This may sound extreme but it did eject the CD but its not recommend.Worse case scenario is that you remove the unit using these special tools and then take the unit apart and manually wind the CD out.I hope this helps, but please do check the fuse number for the Infotainment system as it may be different to my Astra.
Upgrading the D70 FirmwareUpgrading the D70 FirmwareWindowsThank you for choosing a Nikon product. This guide describeshow to upgrade the camera firmware for the D70.If you are not confident that you can perform the update successfully, theupdate can be performed by a Nikon service representative.The D70 has two sets of firmware, A and B, which must be updated separately.After updating the A firmware, repeat steps 45, below, to upgradethe B firmware.ImportantThe D70 may be damaged if power is interrupted or camera controls areoperated during the update. Do not turn the camera off, remove or disconnectthe power source, or operate camera controls during the update.